Back to Listings

2018 Peterbilt 567

VIN # 482915

This new 2018 Peterbilt 567 is now available at Stahl Peterbilt. For more information, give us a call at 800.252.7981.

Specifications

  • Engine MakePaccar
  • Engine ModelMX-13
  • Horsepower510
  • Wheelbase260
  • TransmissionEaton
  • Transmission ModelFO18E313A-MHP
  • Transmission Speeds13
  • Interior StylePrestige
  • Paint ColorWhite
  • Rig UpWet Vac

Details

  • HoodAlum 115 Voc
  • DescriptionVocational - Class 8
  • Front Axle MakePaccar
  • Rear Axle ModelRZ-XX166P
  • Axle Ratio4.1
  • Rear Suspension ModelAIR TRAC
  • Interior ColorSterling Gray
  • Diff LocksSmart Atc
  • Rear Susp MakePeterbilt
  • LOCKED: Ignore On Updatetrue

  • 92 bbl Vacuum System
    • 72" x 17 ft. long seam to seam tank x 5/16" thick
    • 3/8 angle tank pedestals
    • Flat bar reinforcement rings
    • Roll bars installed on top of tank
    • Front tank lock down system c/w actuator and new code tie downs
    • No inside partial baffle - BUT weld in baffle brackets only
    • Recessed liquid level indicator on drivers side
    • 4" NVE load valve on D/S c/w air actuator and 6" sandpipe
    • 4" NVE discharge valve on P/S c/w air actuator
    • 6" NVE dump valve c/w air actuator
    • Cab control for 6" dump valve
    • Aluminum camlocks c/w dust caps
    • Hydraulically operated full opening rear head c/w 6 capped wing bolts
    • Rear door top locking mechanism to support door in the open position
    • No post style rear door lock system on P/S to tank door
    • Robuschi RB-DV-85 PD blower - mounted behind the cab
    • Positive displacement lobe type blower
    • Intake air cooling system
    • Back flow check valve
    • 6" - 4-way vacuum pressure selector valve
    • Maximum vacuum 27" Hg
    • Recommended speed 3400 RPM
    • 96 maximum H.P.
    • 6" Port size
    • Intake and discharge silencers
    • 6" plumbing c/w loop hose which allows tank to be raised or lowered while connected to blower
    • Exhaust out passenger side c/w 45 deg. outlet, camlock and cap
    • 6" primary fluid shut-off
    • Cartridge type filter assembly c/w filter housing
    • 6" centrifugal cyclone filter fluid shut-off
    • Isolation valve c/w air control valve
    • Combination vacuum/pressure guages, relief valves and tank vent
    • 150" - 4 stage front hydraulic hoist c/w full length HSS sub-frame and rear hinge assemblies
    • Tank safety support stand to secure tank in the raised position
    • Hydraulically driven vibrator c/w bottom mounts and control valve
    • 8-bolt air shift PTO with greaseable shaft c/w cab control
    • LINDE close loop piston hydraulic pump c/w piggy back pump coupled to PTO
    • LINDE piston hydraulic motor direct coupled c/w driver coupler
    • 90 gal. hydraulic oil reservoir c/w inspection cover, breather, therm., site glasses & return filter
    • Hydraulic cooler c/w bypass and 12 volt cooling fan
    • Joystick control (blower) & hydraulic control valve for allied functions installed on D/S side front
    • No two blower on/off switches - 1 in cab and 1 on D/S
    • All necessary hydraulic hoses and fittings
    • Full length inside agitator pipe c/w solid shafts on each end and stirring arms
    • Bearings, vacuum/pressure seals installed in housings on each hardened end shaft
    • Oil pressure chamber to keep positive pressure in bearing housings c/w warning light
    • Hydraulic drive motor installed on one end of agitator c/w reduction drive system
    • Cab control valve to operator agitator hydraulic system c/w hose & fittings
    • Full length subframe with checker plate storage tray fenders with cut outs c/w mudflaps
    • Blower and hydraulic reservoir mounting stand
    • 1" square tubing hand railing welded to decking on each side of unit
    • Full width code rear bumper with 24" center cut out
    • 96" deck mounted tool box c/w 3 doors
    • (2) 48" vertical cabinet on each installed P/S and D/S of decking c/w door, shelf, & light
    • Hot water heat in D/S cabinet
    • No hydraulic driven 3" T&E pump c/w circulating pump, silicon water lines and valves
    • Hot water jacket on cyclone ball valve drain c/w silicon water line
    • Hot water jacket on isolation valve at primary c/w silicon water line
    • Ladder rungs on side of tank
    • FLIP style placard holders
    • Hour meter installed for PTO
    • 30# fire extinguisher c/w mounting bracket
    • Two sliding type double chains hooks
    • Manual rewind static ground reel
    • Extra mud flaps installed ahead of hydraulic tank
    • Posi-ground system c/w 2nd ground reel and alarms
    • Posi-ground system to include red beacon light on rear door if ground is lost
    • Cab to have indicator light when hoist is up
    • DOT approved LED tail and marker lights with top & bottom sets at rear
    • 6 working lights (2 front & 4 rear)
    • 6 extra marker lights (3 each side)
    • All electrical installed in weather proof plastic loom with junction boxes
    • Electric brake controller installed and wired to rear
    • 7-wire plug for rig shack wired into rear light bar
    • Sandblasted and painted with Endura paint in 2 colors (1 on tank and 1 on decking)
    • Rock guard: fenders, bumpers, skirting, tool boxes, 20" strip on P/S of tank





Back to Listings

Need More Information?

Use the form below to contact us with your questions or comments and we will respond to you within one business day. Alternatively you can contact us by calling 800.252.7981 in Edmonton, 888.539.5414 in Grande Prairie, or 866.715.5111 in Fort McMurray.

Please note that the form contents will be emailed to us